Hydrogenation process in multiphase alloys of Ti-Zr-Mn-V system on the example of Ti42.75Zr27Mn20.25V10 alloy

The influence of phase composition and microstructure of Ti_42.75Zr₂₇Mn_20.25V₁₀ alloy on its hydrogenation kinetic and phase composition of hydrogenated product was studied. It is established that the process of dissociation of hydrogen molecules begins on the surface of Laves phase crystallites. The dissolution of atomic hydrogen in the material volume leads to the formation of cracks in the intermetallic crystallites, which further appear as additional centers of dissociation of hydrogen molecules and noticeably accelerate the diffusion of hydrogen into the bulk material. It was shown that the Laves phase acts as a donor of atomic hydrogen for the BCC solid solution during hydrogenation of two-phase structure, initiating intensive hydrogenation of the BCC phase at room temperature.     

In situ synthesis of Al2O3–SiC powders via molten-salt-assisted aluminum/carbothermal reduction method

Al₂O₃–SiC composite powder (ASCP) was successfully synthesized using a novel molten-salt-assisted aluminum/carbothermal reduction (MS-ACTR) method with silica fume, aluminum powder, and carbon black as raw materials; NaCl–KCl was used as the molten salt medium. The effects of the synthesis temperature and salt-reactant ratio on the phase composition and microstructure were investigated. The results showed that the Al₂O₃–SiC content increased with an increase in molten salt temperature, and the salt–reactant ratio in the range of 1.5:1–2.5:1 had an impact on the fabrication of ASCP. The optimum condition for synthesizing ASCP from NaCl–KCl molten salt consisted of maintaining the temperature at 1573 K for 4 h. The chemical reaction thermodynamics and growth mechanism indicate that the molten salt plays an important role in the formation of SiC whiskers by following the vapor-solid growth mode in the MS-ACTR treatment. This study demonstrates that the addition of molten salt as a reaction medium is a promising approach for synthesizing high-melting-point composite powders at low temperatures.     

气瓶内部淬火过程的流动换热特性

 大直径厚壁气瓶内部淬火时的流动换热过程极其复杂，受到多种因素的影响，而研究气瓶内部压强和温度的变化规律对改善流动换热效果、提高产品组织性能具有重要的理论指导意义。以914 mm厚壁气瓶和瓶内流体为研究对象，建立了二维等效流 固耦合模型；采用多喷嘴系统对气瓶内外进行喷水淬火，研究了气瓶总长、喷水流速及淬火时间对瓶内压强及内壁温度的影响，通过间歇淬火试验验证了数学模型的正确性。结果发现，气瓶长度对瓶内压强和瓶壁温度的影响显著，喷水流速次之，当喷水流速大于8 m/s后，水量对瓶壁的冷却效果大大降低；气瓶内壁长度方向的温度梯度分别随气瓶总长的增加和淬火时间的延长而减小，但基本不受喷水量的影响。     

Influences of the inner diameter of the solid shielding tube on the characteristics of the radio-frequency cold atmospheric plasma jet

Active control of the local environment of the cold atmospheric plasma (CAP) jet is of great importance in actual applications since the CAP operates in an open atmosphere with the inevitable entrainment of the surrounding cold air. In this paper, the solid shielding effects of the cylindrical quartz tubes with different inner diameters on the characteristics of the CAP jets driven by a radio-frequency (RF) power supply are studied experimentally. The experimental results show that the total length of the shielded plasma jet can be increased significantly by an appropriate combination of the quartz tube inner diameter and that of the plasma generator nozzle exit with other parameters being unchanged. This phenomenon may be qualitatively attributed to the loss of diffusion of the charged particles in the radial direction under different inner diameters of the quartz tubes. Compared with the plasma free jet, the plasma shielding jet is produced with optimized parameters including longer plasma jet length, higher concentrations of chemically reactive species, higher rotational, vibrational, and electron excitation temperatures when the inner diameters of the solid shielding tube and the generator nozzle exit are the same. A maximum plasma jet length of 52.0 cm is obtained in contrast to that of 5.0 cm of the plasma free jet in this study. The experimental results indicate that the solid shielding effect provides a new method for the active control of the local environment of the RF-CAP jet operating in an open atmosphere.     

Multiphase topology optimization with a single variable using the phase-field design method

In this study, a multimaterial topology optimization method using a single variable is proposed by combining the solid isotropic material with penalization method and the reaction-diffusion equation. Unlike ordinary multimaterial optimization, which requires several variables depending on the number of material types, this method intends to represent various materials as one variable. The proposed method combines two special functions in the sensitivity analysis of the objective function to converge the design variable into prespecified density values defined for each of the multimaterials. The composition constraint based on a normal distribution function is also introduced to estimate the distribution of each target density value in a single variable. It enables density exchange between multiple materials by increasing or decreasing the amount of a specific material. The proposed method is applied to structural and electromagnetic problems to verify its effectiveness, and its usefulness is also confirmed from the viewpoint of cost and computation time.     

稀土La2O3改性脲醛树脂的黏度特性研究

脲醛树脂(UF树脂)胶黏剂具有胶合强度高、制作简单、成本低廉、原料来源丰富等一系列特点,成为我国人造板生产的主要胶种,是市场上需求量最大的胶黏剂之一。但由于在固化时会放出刺激性的甲醛,游离甲醛高,在使用时严重危害人的健康。近年来,随着人们环保意识的提高,生产和使用低毒UF树脂胶势在必行。本文介绍了稀土氧化镧对脲醛树脂的改性过程并对改性后脲醛树脂胶的各项性能进行了测试。本实验通过在不同反应阶段加入稀土氧化镧,分别探讨它们对脲醛树脂胶黏剂性能影响。实验表明:在脲醛树脂胶中加入稀土氧化镧可以增加黏度、固化时间、固含量,并可以减少游离甲醛释放量。     

热处理对挤压态Mg-6Gd-5Y-1Zn合金组织与性能的影响

通过对Mg-6Gd-5Y-1Zn(质量分数,%)合金在固溶和时效处理状态下显微组织和力学性能的研究发现,α-Mg基体、沿挤压方向分布的条状18R-LPSO相、少量的Mg₂₄(GdYZn)₅ 相以及细层片状的14H-LPSO相构成了挤压态合金的组成相。挤压态合金经固溶(T4)处理后,一部分18R-LPSO相溶入基体,并且基体中的14H-LPSO相伸长同时粗化。挤压态合金经过固溶加时效(T6)处理后,大量β′相从α-Mg基体中析出。T6态合金的室温力学性能最好,其屈服强度、抗拉强度及伸长率分别为272 MPa、406 MPa和6.1%。β′相沉淀也发生在挤压态合金的直接人工时效(T5)处理过程,但相比于T6处理,14H-LPSO相和β′相在基体中的体积分数均偏低。     

激光立体成形TC4钛合金的热力场演化

激光立体成形能够实现高性能复杂零件的精确成形，但成形过程中的高温度梯度极易导致残余应力和变形，最终影响构件的几何精度和力学性能。通过搭建基板单边夹持原位热变形测量系统，探究了多道多层TC4钛合金成形件在激光立体成形过程中基板温度、变形的演化规律，分析了不同扫描策略对构件热应力场的影响。研究结果表明，构件的变形发展受其热历史驱使，扫描策略对成形件的热变形具有显著影响。     

Covalent triazine framework with efficient photocatalytic activity in aqueous and solid media

Covalent triazine frameworks (CTFs) have been recently employed for visible light-driven photocatalysis due to their unique optical and electronic properties. However, the usually highly hydrophobic nature of CTFs, which originates from their overall aromatic backbone, leads to limitations of CTFs for applications in aqueous media. In this study, we aim to extend the range of the application media of CTFs and design hybrid material of a CTF and mesoporous silica (SBA-15) for efficient photocatalysis in aqueous medium. A thiophene-containing CTF was directly synthesized in mesopores of SBA-15. Due to the high surface area and the added hydrophilic properties by silica, the hybrid material demonstrated excellent adsorption of organic molecules in water. This leads not only to high photocatalytic performance of the hybrid material for the degradation of organic dyes in water, but also for efficient photocatalysis in solvent-free and solid state. Furthermore, the reusability, stability and easy recovery of the hybrid material offers promising metal-free heterogeneous photocatalyst for broader applications in different reaction media.